Index: DamEngine/trunk/src/Deltares.DamEngine.IntegrationTests/IntegrationTests/MacroStabilityInwardsTests.cs
===================================================================
diff -u -r6027 -r6029
--- DamEngine/trunk/src/Deltares.DamEngine.IntegrationTests/IntegrationTests/MacroStabilityInwardsTests.cs	(.../MacroStabilityInwardsTests.cs)	(revision 6027)
+++ DamEngine/trunk/src/Deltares.DamEngine.IntegrationTests/IntegrationTests/MacroStabilityInwardsTests.cs	(.../MacroStabilityInwardsTests.cs)	(revision 6029)
@@ -939,13 +939,13 @@
         });
     }
 
-    [Test, Category(Categories.WorkInProgress)]
-    [TestCase("DWP_1", InputStabilityModelType.Bishop, "SlopeAdaptionBeforeShoulderAdaption", CalculationResult.Succeeded, 1.4, 1.456, 5)]
-    [TestCase("DWP_1", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.Succeeded, 1.4, 1.520, 4)]
-    [TestCase("DWP_2", InputStabilityModelType.Bishop, "SlopeAdaptionBeforeShoulderAdaption", CalculationResult.RunFailed, 1.5, 1.348, 14, "After height adaption ditch does not fit inside surfaceline anymore.")]
-    [TestCase("DWP_2", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 1.072, 17)]
-    [TestCase("DWP_13", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 0.943, 23, "The characteristic points of the surfaceline are not ascending in X-direction.")]
-    [TestCase("DWP_10", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 0.0, 7, "Location 'DWP_10', subsoil scenario 'DWP_10.stix', design scenario '3': The calculation failed with error message 'The design was not successful. The design was not successful. Stability calculation failed.'", "The design was not successful. Stability calculation failed.")]
+    [Test, Category(Categories.Slow)]
+    [TestCase("DWP_1", InputStabilityModelType.Bishop, "SlopeAdaptionBeforeShoulderAdaption", CalculationResult.Succeeded, 1.4, 1.493, 5)]
+    [TestCase("DWP_1", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.Succeeded, 1.4, 1.545, 4)]
+    [TestCase("DWP_2", InputStabilityModelType.Bishop, "SlopeAdaptionBeforeShoulderAdaption", CalculationResult.Succeeded, 1.5, 1.546, 9)]
+    [TestCase("DWP_2", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 1.176, 17, "Location 'DWP_2', subsoil scenario 'DWP_2.stix', design scenario '1': The calculation failed with error message 'The design was not successful. After height adaption ditch does not fit inside surfaceline anymore.'")]
+    [TestCase("DWP_13", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 0.936, 23, "The characteristic points of the surfaceline are not ascending in X-direction.")]
+    [TestCase("DWP_10", InputStabilityModelType.Bishop, "OptimizedSlopeAndShoulderAdaption", CalculationResult.RunFailed, 1.5, 1.308, 16, "Location 'DWP_10', subsoil scenario 'DWP_10.stix', design scenario '3': The calculation failed with error message 'The design was not successful. After height adaption ditch does not fit inside surfaceline anymore.'")]
     [TestCase("DWP_1", InputStabilityModelType.BishopUpliftVan, "SlopeAdaptionBeforeShoulderAdaption", CalculationResult.Succeeded, 1.4, 1.406, 6)]
     public void GivenTutorialDesign_WhenSpecifiedLocationRunWithGeometryAdaption_ThenGivesExpectedResults(string locationId, InputStabilityModelType stabilityModelType, string designMethod,
                                                                                                           CalculationResult calculationResult, double requiredSafetyFactor, double actualSafetyFactor, int iterationCount, string errorMessage = "", string firstStabilityMessage = "")