Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/Calculation.tex
===================================================================
diff -u -r6509 -r6786
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/Calculation.tex	(.../Calculation.tex)	(revision 6509)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/Calculation.tex	(.../Calculation.tex)	(revision 6786)
@@ -12,7 +12,3 @@
 The adaptation must have the options to increase the crest, change the angle of the slope, 
 create a berm or a combination of these options according to given settings.
 
-\section{Perform Calamity calculation}\label{sec:USCalculationCalamity}
-It should be possible to make a calculation in a Calamity project. 
-After importing a time series of water levels the safety factors will be calculated for all locations and for all time steps.
-
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex
===================================================================
diff -u -r6514 -r6786
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex	(.../DAM_UI_FO.tex)	(revision 6514)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex	(.../DAM_UI_FO.tex)	(revision 6786)
@@ -53,7 +53,6 @@
 Added more functional requirements.
 \begin{itemize}
 	\item Create Design project.
-	\item Create Calamity project
 	\item Perform Design calculation - No adaption.
 	\item Perform Design calculation - With adaption.
 	\item Display results in graphic view.
@@ -88,10 +87,6 @@
 I can either just calculate the safety factors of the current situation or design (adapt geometry) to a required safety factor.
 The design of this functionality is described in \autoref{sec:USCreateDesignProject}.
 
-\section{User story Create Calamity project}
-As a geotechnical engineer I want to create a Calamity project in which I can import project information and perform calculations based on a time serie of water levels and evaluate the results.
-The design of this functionality is described in \autoref{sec:USCreateCalamityProject}.
-
 \section{User story DAMLive configuration}
 As a geotechnical engineer I want to make a DAMLive configuration, so that I can make calculations with DAM engine, using sensors for the input of piezometric lines. 
 The design of this functionality is described in \autoref{sec:USDAMLiveConfiguration}.
@@ -126,11 +121,6 @@
 create a berm or a combination of these options according to given settings.
 The design of this functionality is described in \autoref{sec:USCalculationDesignWithAdaption}.
 
-\section{User story Perform Calamity calculation}
-As a geotechnical engineer I want to be able to make a calculation in a Calamity project. 
-After importing a time series of water levels the safety factors will be calculated for all locations and for all time steps.
-The design of this functionality is described in \autoref{sec:USCalculationCalamity}.
-
 \section{User story Display results in table form}
 As a geotechnical engineer I want to see the results of the calculations, so I can evaluate the calculations. 
 The design of this functionality is described in \autoref{sec:USDisplayResultsTable}.
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/ResultsDisplay.tex
===================================================================
diff -u -r6514 -r6786
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/ResultsDisplay.tex	(.../ResultsDisplay.tex)	(revision 6514)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/ResultsDisplay.tex	(.../ResultsDisplay.tex)	(revision 6786)
@@ -107,9 +107,6 @@
 	\item The resulting slipcircle when a stability calculation has been performed.
 \end{itemize}
 
-\subsection{Time series of safety factors}
-When a Calamity project has been calculated it should be possible to view a chart per location with a time series of the safety factors.
-
 \section{Open individual D-Stability projects}\label{sec:USOpenDStability}
 When a stability calculation has been performed it should be possible to open the stability calculation 
 in D-Stability for each calculated (design and/or subsoil) scenario per location.
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CreateProject.tex
===================================================================
diff -u -r6514 -r6786
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CreateProject.tex	(.../CreateProject.tex)	(revision 6514)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CreateProject.tex	(.../CreateProject.tex)	(revision 6786)
@@ -10,12 +10,6 @@
 When this value is not met with the initial calculation, then a new surfaceline is determined, 
 which will result in a safety factor that complies to the required value. 
 
-\section{Create Calamity project}\label{sec:USCreateCalamityProject}
-When the data sources are correctly defined the user should be able to create a Calamity project.
-If the creation fails a log should display the problems encountered.
-This project can be used to perform a calculation of safety factors during a certain amount of time. 
-A time series of waterlevels has to be provided for this calculation.
-
 \section{DAMLive configuration}\label{sec:USDAMLiveConfiguration}
 When the data sources are correctly defined and a separate configuration file for the sensor data is provided, 
 the user should be able to create a DamLive configuration.