Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/OpenProject.tex
===================================================================
diff -u -r6807 -r6868
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/OpenProject.tex	(.../OpenProject.tex)	(revision 6807)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/OpenProject.tex	(.../OpenProject.tex)	(revision 6868)
@@ -8,7 +8,7 @@
 The user must be able to open an existing project. 
 When calculations were made, also the calculation results must be shown.
 The results will not be shown when made by a previous version of \ProgramName, because the results can be outdated. \newline
-\Note{In version 25.1 it is not possible to open previous \ProgramName (*.damx) projects because there were too much changes. 
+\Note{In version 26.1 it is not possible to open previous \ProgramName (*.damx) projects because there were too much changes. 
 A workaround for this is to recreate the project again with the original source data 
 (see \autoref{sec:USCreateDesignProject}).}
 
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex
===================================================================
diff -u -r6786 -r6868
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex	(.../DAM_UI_FO.tex)	(revision 6786)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DAM_UI_FO.tex	(.../DAM_UI_FO.tex)	(revision 6868)
@@ -53,6 +53,7 @@
 Added more functional requirements.
 \begin{itemize}
 	\item Create Design project.
+	\item Create Calamity project
 	\item Perform Design calculation - No adaption.
 	\item Perform Design calculation - With adaption.
 	\item Display results in graphic view.
@@ -65,6 +66,12 @@
 	\item Undo-Redo.
 \end{itemize}
 
+\subsection{Revision 0.4}
+\label{sec:Revision03}
+Removed functional requirement:
+\begin{itemize}
+	\item Create Calamity project
+\end{itemize}
 
 \chapter{Non-functional requirements}
 
@@ -87,6 +94,10 @@
 I can either just calculate the safety factors of the current situation or design (adapt geometry) to a required safety factor.
 The design of this functionality is described in \autoref{sec:USCreateDesignProject}.
 
+\section{Obsolete: User story Create Calamity project}
+As a geotechnical engineer I want to create a Calamity project in which I can import project information and perform calculations based on a time serie of water levels and evaluate the results.
+The design of this functionality is described in \autoref{sec:USCreateCalamityProject}.
+
 \section{User story DAMLive configuration}
 As a geotechnical engineer I want to make a DAMLive configuration, so that I can make calculations with DAM engine, using sensors for the input of piezometric lines. 
 The design of this functionality is described in \autoref{sec:USDAMLiveConfiguration}.
@@ -121,6 +132,11 @@
 create a berm or a combination of these options according to given settings.
 The design of this functionality is described in \autoref{sec:USCalculationDesignWithAdaption}.
 
+\section{Obsolete: User story Perform Calamity calculation}
+As a geotechnical engineer I want to be able to make a calculation in a Calamity project. 
+After importing a time series of water levels the safety factors will be calculated for all locations and for all time steps.
+The design of this functionality is described in \autoref{sec:USCalculationCalamity}.
+
 \section{User story Display results in table form}
 As a geotechnical engineer I want to see the results of the calculations, so I can evaluate the calculations. 
 The design of this functionality is described in \autoref{sec:USDisplayResultsTable}.